Getting Started with Plumber's Essentials When Installing a Bathtub
Getting Started with Plumber's Essentials When Installing a Bathtub
Blog Article
Just how do you actually feel about Tools You Need to Install a New Bathtub ?
Installing a bath tub isn't precisely rocket science, but it does require strong plumbing, carpentry, and in some cases, tiling skills. Changing an old tub with a new one is also a moderately difficult project. If the old bathtub is easily easily accessible, the task can move rapidly; if you have to open up a wall to remove the old tub and also position the brand-new tub, the task is much harder. In either case, the task is within a residence handyman's abilities, although you will certainly require a helper to move out the old bathtub and set in the new one. Make sure you have actually qualified on your own for the job and are comfortable trying it. Rather than working with a service provider to take over a halfway-completed task, it is much better to consider using one prior to you start. Chances are you might require a professional plumber to make tube connections.
This write-up will assist you mount a brand-new bath tub in your shower room if you have currently gotten a new tub as well as don't require to alter the arrangement of your previous supply of water pipelines.
Your devices and also material list must consist of the following:
Removing Old Taps
If you require to replace old taps with brand-new ones as a part of your installation, then the first thing you must do is disconnect the supply of water. After doing so, switch on the taps to drain any type of water remaining in the system. The procedure of getting rid of the existing faucets can be quite problematic because of the restricted access that is commonly the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the remaining water that will originate from the pipelines. As soon as the supply pipelines have been eliminated, make use of the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single faucets from turning throughout this process. Once the faucets have actually been removed, the holes in the bath/basin will need to be cleansed of any type of old securing substance.
Prior to carrying on to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Taps
If the tails of the new faucets are plastic, then you will certainly require a plastic connector to avoid damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end supplies a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will call for lowering couplers, which connects the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next off, place the tap in the mounting hole in the bath/basin guaranteeing that the washing machines are in location between the tap and also the sink. Secure the tap in position with the supplier given backnut. When the tap is safely in position, the supply pipelines can be connected to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet adapters. The former kind should be attached to the faucet ends initially, tightening up only by hand. The supply pipes can later be connected to the other end. Tighten both ends with a spanner after both ends have actually been attached.
Installing the Bath tub
Making use of the two wooden boards under its feet, put the bathtub in the required setting. The wood boards are valuable in uniformly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto 4 small points.
The next goal is to make certain that the tub is leveled all round. This can be achieved by examining the spirit level and readjusting the feet on the bathtub till the level checks out degree.
To install faucets, fit all-time low of the furthest adaptable faucet connector to the appropriate supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Turn on the water system as well as inspect all joints and also brand-new pipework for leaks and also tighten them if essential. Fill up the bath tub as well as likewise inspect the overflow outlet and the regular outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the producer's instruction manual. Tiling and sealing around the tub must wait till the tub has been utilized a minimum of when as this will certainly resolve it right into its last setting.
Preparing for the Installment
First of all, the sustaining structure supplied with the bathroom should be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to ensure that if the tap features a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to prevent strain on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets making use of 2 nuts as well as olives (often supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you use every one of the provided washing machines.
Connect the trap to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect all-time low of the overflow tube in a similar manner.The bath must currently be ready to be suited its final placement.
Tiling Around the Tub
In the area where the bath fulfills the ceramic tile, it is required to secure the accompanies a silicone rubber caulking. This is necessary as the installation can move sufficient to fracture a rigid seal, causing the water to permeate the wall in between the bath and the tiling, bring about issues with moisture and also possible leaks to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and installations. They are offered in tubes and also cartridges, and also can securing voids as much as a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked newspaper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to sealing, to allow for the activity experienced when the tub remains in use. The sealer can break relatively early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily offered on the marketplace. It is a good idea to fit the tiles using water-resistant or waterproof sticky and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I found that post on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround while doing a lookup on the web. Sharing is caring. Helping others is fun. Bless you for your time. Come back soon.
Protect your home, dial! Report this page